How To Remove Sediment From Hot Water Heater or Tap Well water?

How to remove sediment from water heater? As we all know, tap water and well water contain a lot of minerals and sediment. After the water is heated in the water heater, it will produce some sedimentation. Some turbid sewage and sediment scales will be deposited at the bottom of the water heater. It will not only block the pipeline but also affect the water quality and breed bacteria. So how to remove sediment from the water heater? This article will provide you with practical methods of how to avoid a large amount of sediment in household tap or well water.

Is sediment in water harmful?

Yes! Before we get into the solutions of how to remove sediment from water heater, let's briefly understand the harm of sediment and scale in electric water heaters.

1. Sediment in water will make the water quality worse and endanger skin health

Why do we remove sediment from water heater? The bacteria contained in the water of the electric water heater will cause certain irritation to the skin. The elderly, children, and people with sensitive skin, bathing with such unclean water are prone to itching, redness, and other skin problems.

Harmful substances such as scale, sediment, and rust deposited in the inner tank of the electric water heater will damage the skin epidermis and stimulate the skin to produce chronic inflammation. As a result, it will cause aging and roughness of the skin. These scales and impurities will fall off and enter the pipes, blocking the pipes, especially in the finer showers, faucets, etc.

2. Sediment in water will make the water output small, affecting the bathing experience

The deposited scale occupies a large amount of the inner tank space, resulting in a decrease in the available hot water. And the scale will block the shower, resulting in a decrease in water output, affecting normal use.

3. Sediment deposits in the water will make the electric water heater heat slowly

The electric water heater has a heating rod inside. After the scale is generated, it is wrapped around the heating rod. The thermal conductivity of the scale is relatively poor, which causes the heat generated by the heating rod to be unable to be quickly transferred to the water, resulting in two problems. The first is that the heating speed is slow, the water can be boiled in 1 hour, and it may take 1.5 hours for more scale. The second is the cost of electricity because the heating time required is long. The heating speed of the electric water heater will become slower and slower after a period of use, mainly because the scale attached to the heating tube causes the heat to be unable to dissipate quickly, thereby accelerating the aging of the heating tube, resulting in greater resistance and a decrease in power.That is also the reason why we should remove sediment and scale from water heater.

4. There is a hidden danger of electricity use in water full of sediment

If the electric water heater is not cleaned regularly, the excessive scale may put it at risk of pipe bursting. In addition, impurities in the water will cause pitting corrosion on the surface of the heating pipe, reduce the service life of the water heater, and there are greater safety hazards. In the process of generating scale, it is corrosive to metals. Those water heaters that explode and leak are all because the inner tank has been corroded and cracked.

How to Remove Water Sediment?

After knowing the harm of sediment and scale, let's teach you how to remove sediment from water. Below we divide the sediment of well water, sediment and scale in a water heater, scale in water pipes, and scale in faucets to help you.

1. How to Get Rid of Sand in Well Water?

How to get rid of sand in well water? The reason why the well water has sand may be because there is too much soil in the well where the well is drilled and is not very strong. When the water in the soil flows into the well, it will carry the loose sand on the wall of the well to the water in the well. The effective solution to this problem is to find another place to drill a well. Because the location of the well is more important. If there is sediment, if it cannot be treated, there is no way to use it. So we can consider changing a place and re-operating. However, if you do not want to change the place and re-operate, we can consider installing a quartz sand filter for treatment.

2. How to Remove Sediment from Hot Water Heater？

Then how to remove sediment and scale from a hot water heater? First of all, we need to pay attention to our usage habits and do the following two points

1. Set the low temperature. Especially for electric water heaters, the maximum temperature can generally reach 75 °C or even 80 °C. But this temperature is for temporary use - for example if a guest suddenly comes to the house and the amount of hot water is not enough, you can increase the amount of warm water by increasing the water temperature. For daily use, it is recommended to set the temperature at about 50°C. This is because the rate of scale production is directly related to temperature. As the temperature increases, the rate of scale production increases exponentially.

2. Emptying the water in the water heater. If you don't use a water heater for a long time, you should drain all the water inside. Do not allow water to accumulate in the water heater, because the impurities in the water will slowly settle and adhere to the inner tank. There is no clear definition of how long it takes to empty the water heater when it is not used, and it is related to the quality of your local water.

Habits can only reduce the production of scale, but if you want to completely eliminate scale, you must also match a pre-filter. In fact, the pre-filter, as it literally means, is filter equipment installed in the front of the pipeline for pretreatment or coarse filtration. The pre-filter can filter 40-120μm of particulate impurities so that the water quality is restored to the factory standard of the waterworks. The range of use is also very wide, suitable for both home installation and commercial installation, which can remove pollution and avoid pipeline rust.

The pre-filter, which looks simple, is really useful in practice. It can greatly improve the quality of our daily water. It can not only block large particles of impurities such as particles, colloids, suspended solids, sediment, rust, and insect eggs in household water, but also play a positive role in protecting our indoor wading appliances (such as washing machines, water heaters, floor heating, dishwashers, water softeners, etc.). So if you ask how to remove sediment from the water heater, installing a pre-filter is your best choice to remove sediment and scale in water. As the first pass of household water, pre-filter plays an irreplaceable role in the purification of household water, which is yourr best solutions to how to remove sediment from water heater. If you want to buy a pre-filter, these three prefilters are much recommended.

1. SimPure V7 water filter for under the kitchen sink

2. SimPure DC5P spin down sediment filter

3. SimPure DC3S home anti-scale filter

(For each sediment pre-filter, you can click the pictures to the product page.)

Also, if you want to clean the sediment from your water heater, you can also turn on the water heater to clean it up. However, it is best not to clean the water heater by yourselves but with professional cleaners. Firstly, there is no professional equipment for you to clean. Secondly, your operation may be unprofessional and careless, which will damage the water heater. For more products on whole house sediment filter, you can visit here.

3. How to Remove Sediment from Water Lines?

Here are three ways of how to remove sediment from water lines.

---Use the wire head to dredge: pour a small amount of water into the sewer, extend the wire into the sewer, lift back and forth so that the sand and mud dissolve in the water and discharge together, and then rinse with clean water.

---Use water pressure dredging: Use a water pipe to connect the sewer and faucet, then turn the faucet to the maximum. And then you gradually push the mud and sand of the sewer through the water flow until it is discharged into the gutter.

---Open the pipe to remove: The sand and mud of the sewer are generally accumulated at the bend of the sewer. You can use professional tools to disassemble the sewer pipes, remove the dirt and sand inside, and rinse them with clean water to ensure complete unclogging.

4. How to Clean Sediment from Faucet?

There are reasons for sand in the faucet, one is that sand and other particles are left in the faucet when the faucet is renovated and installed; The second is the impurities brought by the water supply source. So how to clean sediment from faucet? At this time, we can remove the filter screen in the faucet for cleaning. For impurities adhering to the filter screen, we can use toothpicks or sewing needles to remove them. However, when disassembling and cleaning the filter, pay attention to controlling the force and the direction of removal, so as not to damage other parts of the faucet. After cleaning up, reinstall the filter, and the problem will be solved.

To prevent faucets from forming sand deposits that affect household water use, we can purchase filtration products to filter the incoming water. For example, a pre-filter such as a tap water filter can be installed behind the main valve of tap water at home to carry out simple and rough filtration of large sand, rust, and other impurities. In terms of price, pre-filters are generally cheaper and more durable. Households with poor water quality can refer to purchase of a filter faucet.

In conclusion, there are all methods of how to remove sediment from water heater and tap well water. If you are interested in whole-house water filtration, you can take a look at sediment water filter to give you the best home water purification solution.